water lubricated cutlass bearings (with bronze or phenolic shell) Available for shaft diameters between Ø 20 mm and Ø 100 mm and from Ø 1″ throught Ø 4″. Polyurethane-rubber lining. Outer bushings made of either bronze or phenolic resin. Phenolic resin is lighter in weight, cannot corrode and may be replaced very easily. Ideally suited for use in aluminum boats.
Cutless
|
All dimensions are in mm.
|
|
ØD
|
A
|
B
|
C
|
J
|
W
|
|
25
|
|
|
127
|
40
|
112
|
|
30
|
|
|
172
|
57
|
112
|
|
35
|
184
|
54
|
112
|
||
|
40
|
|
|
206
|
64
|
114
|
|
45
|
226
|
69
|
129
|
||
|
50
|
254
|
79
|
129
|
Dependent on length, diameter and number of shaft revolutions, 1, 2 or 3 cutlass bearings must be installed (see below)
Bronze stern tube with one cutlass bearing, aft.
|
Ø D
|
B
|
Ø G
|
K
|
Ø Q
|
|
25
|
on request
|
43
|
8
|
51
|
|
30
|
on request
|
49
|
10
|
54
|
|
35
|
on request
|
56
|
10
|
60
|
|
40
|
on request
|
61
|
12
|
63.5
|
|
45
|
on request
|
71
|
12
|
70
|
|
50
|
on request
|
76
|
12
|
76
|
Bronze stern tube with two cutlass bearing. one forward and one aft.
Bronze stern tube with three cutlass bearings (forward, aft and intermediate). When ordering, please specify dimensions A, B and C
Remanit 4462 propeller shaft, completely machined and with propeller nut with
integrated zinc anode. Dimensions
of taper and keyway in accordance with ISO 4566.
Self-aligning inner bearing.
The VETUS (flexible) inner bearing used in this system has dual sealing lips, as double security against water leakage.
|
Ø D
|
Length A
|
F
|
I
|
O
|
Y
|
Z
|
|
25
|
on request
|
8
|
3
|
M16x1.5
|
25
|
55
|
|
30
|
on request
|
8
|
3
|
M204x1.5
|
30
|
75
|
|
35
|
on request
|
10
|
3
|
M24x2
|
35
|
85
|
|
40
|
on request
|
12
|
3
|
M24x2
|
35
|
95
|
|
45
|
on request
|
14
|
3.5
|
M30x2
|
40
|
105
|
|
50
|
on request
|
14
|
3.5
|
M36x3
|
45
|
115
|
|
D
|
V
|
X
|
|
Ø 25
|
112
|
144
|
|
Ø 30
|
112
|
144
|
|
Ø 35
|
112
|
145
|
|
Ø 40
|
114
|
150
|
|
Ø 45
|
129
|
165
|
|
Ø 50
|
129
|
165
|
|
Ø 60
|
129
|
168
|
There are two possibilities of water lubrication for these shaft assemblies:
1. by means of a water scoop G 3/8, with ball valve, hose pillar, 1 m of water hose and hose clamps (optional kit)
2. by tapping a small amount of water from the main engine’s raw water cooling circuit.
There are two possibilities of water lubrication for these shaft assemblies:
1. by means of a water scoop G 3/8, with ball valve, hose pillar, 1 m of water hose and hose clamps (optional kit)
2. by tapping a small amount of water from the main engine’s raw water cooling circuit.
|
For shafts with diameter in mm and stern tubes with inside diameters in inches
|
For shafts with diameter in mm and stern tubes with inside diameters in mm
|
For shafts with diameter in inches and stern tubes with inside diameters in inches
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
|
