Tel: 002 0106 8830 786 | Mail: info@dolphin-marine.net



Cutless

    water lubricated cutlass bearings (with bronze or phenolic shell) Available for shaft diameters between 20 mm and 100 mm and from 1" throught 4". Polyurethane-rubber lining. Outer bushings made of either bronze or phenolic resin. Phenolic resin is lighter in weight, cannot corrode and may be replaced very easily. Ideally suited for use in aluminum boats.
    FOR STEEL VESSELS


    All dimensions are in mm.
    Ø D
    A
    B
    C
    J
    W
    25
     
     
    127
    40
    112
    30
     
     
    172
    57
    112
    35
    184
    54
    112
    40
     
     
    206
    64
    114
    45
    226
    69
    129
    50
    254
    79
    129
    Dependent on length, diameter and number of shaft revolutions, 1, 2 or 3 cutlass bearings must be installed (see below)


    Bronze stern tube with one cutlass bearing, aft.
    Ø D
    B
    Ø G
    K
    Ø Q
    25
    on request
    43
    8
    51
    30
    on request
    49
    10
    54
    35
    on request
    56
    10
    60
    40
    on request
    61
    12
    63.5
    45
    on request
    71
    12
    70
    50
    on request
    76
    12
    76


    Bronze stern tube with two cutlass bearing. one forward and one aft.


    Bronze stern tube with three cutlass bearings (forward, aft and intermediate). When ordering, please specify dimensions A, B and C


    Remanit 4462 propeller shaft, completely machined and with propeller nut with
    integrated zinc anode. Dimensions
    of taper and keyway in accordance with ISO 4566.



    Self-aligning inner bearing.
    The VETUS (flexible) inner bearing used in this system has dual sealing lips, as double security against water leakage.
    Ø D
    Length A
    F
    I
    O
    Y
    Z
    25
    on request
    8
    3
    M16x1.5
    25
    55
    30
    on request
    8
    3
    M204x1.5
    30
    75
    35
    on request
    10
    3
    M24x2
    35
    85
    40
    on request
    12
    3
    M24x2
    35
    95
    45
    on request
    14
    3.5
    M30x2
    40
    105
    50
    on request
    14
    3.5
    M36x3
    45
    115
    D
    V
    X
    Ø 25
    112
    144
    Ø 30
    112
    144
    Ø 35
    112
    145
    Ø 40
    114
    150
    Ø 45
    129
    165
    Ø 50
    129
    165
    Ø 60
    129
    168
    There are two possibilities of water lubrication for these shaft assemblies:
    1. by means of a water scoop G 3/8, with ball valve, hose pillar, 1 m of water hose and hose clamps (optional kit)
    2. by tapping a small amount of water from the main engine's raw water cooling circuit.

    For shafts with diameter in mm and stern tubes with inside diameters in inches
    For shafts with diameter in mm and stern tubes with inside diameters in mm
    For shafts with diameter in inches and stern tubes with inside diameters in inches
    A
    B
    C
    20 mm
    1-1/4"
    75 mm
    22 mm
    1-1/4"
    75 mm
    25 mm
    1-1/2"
    100 mm
    30 mm
    1-3/4"
    120 mm
    35 mm
    1-7/8"
    140 mm
    40 mm
    2-1/8"
    160 mm 
    45 mm
    2-3/8"
    180 mm 
    50 mm
    2-5/8"
    200 mm 
    55 mm
    2-7/8"
    220 mm 
    60 mm
    3"
    240 mm 
    65 mm
    3-1/4"
    240 mm 
    70 mm
    4"
    300 mm
     80 mm
    4"
    320 mm 
    A
    B
    C
    25 mm
    40 mm
    100 mm
    30 mm
    45 mm
    120 mm
    35 mm
    50 mm
    140 mm
    40 mm
    55 mm
    160 mm
    45 mm
    65 mm
    180 mm
    50 mm
    70 mm
    200 mm
    60 mm
    80 mm
    240 mm
    70 mm
    90 mm
    280 mm
    80 mm
    100 mm
    320 mm
    90 mm
    110 mm
    360 mm
    100 mm
    125 mm
    400 mm
    A
    B
    C
    1"
    1-1/2"
    4"
    1-1/8"
    1-5/8"
    4-1/2"
    1-1/4"
    1-3/4"
    5"
    1-3/8"
    1-7/8"
    5-1/2"
    1-1/2"
    2"
    6"
    1-5/8"
    2-1/2"
    6-1/2"
    1-3/4"
    2-3/8"
    7"
    2"
    2-5/8"
    8"
    2-1/4"
    3"
    9"
    2-1/2"
    3-1/4"
    10"
    2-3/4"
    3-1/2"
    11"
    3"
    4"
    12"
    3-1/2"
    4-1/2"
    14"
    4
    5
    16"